Wednesday, September 14, 2011

Bad alternator question?

So I tried starting my car the next morning and i found that the battery was dead. So i took it to autozone, and the battery came back good. I put it back in my car n it started up fine! I took my car back to autozone to have the alternator checked and the guy said it was bad! how can this be. If I had my battery checked and it was fine, then the alternator must be doing its job. Also, wouldn't my car cut off while I was driving their if the alternator was bad? I am stumped on what to do now. My battery is 4yrs old, but the guy didn't reccomend changing it out cause it came back good, but reccomended the alternator be changed out. Can anyone shed some light on this. I would greatly appreciate it. ThanksBad alternator question?
dirty battery cables and once you remove battery then they made connection it started anything you think you have a dead battery always start by cleaning cables jump start or charged battery then drive to any shop or parts store check whole system also check your beltBad alternator question?
Your battery must be charged before the ***-hats autozone can test it. Assuming they did that and your battery tested good then yes, your alternator could be bad. Your car will in fact start and run if your alt. is bad so long as there is ample charge in your battery.
  • How to make a baby quilt
  • htc touch case
  • Help I broke my car?

    I own a 1995 Nissan Maxima. Like an idiot, I tried to change my alternator by myself but I snapped in half the slack adjuster bolt for the serpentine belt in the process. How bad is this? Would I be able to drive 25 miles to the nearest mechanic? Would the belt fly off and cause more damage? The belt is tight right now. I did not get a chance to loosen it.Help I broke my car?
    Is the other half of the bolt stuck in the block? If the belt is tight enough it should make it to the shop. Since the bolt broke off in the block, there is a couple of ways to remove it. It can be drilled and tapped or their are some specialty bits that can bite into and unscrew it. If your unable to or don't want to attempt to remove it, a reputable shop should only charge you a couple hours worth of labor. Which depending on where you live will be a couple hundred bucks. This is just to get the broken bolt out. Once out, a new bolt and the old adjuster can go back on. If they tell you that they can't get it out and need a new block, I would go somewhere else. Also depending on how tight a fit it is, some components might have to be removed to get it out which will cost more labor hours and dollars.Help I broke my car?
    go to a mechanicHelp I broke my car?
    I wouldn't chance it. You'll end up on the side of road and who knows what damage you might cause in the attempt. Better call a tow.Help I broke my car?
    no I wouldnt drive it - sounds a bit risky and sorta stupid.Help I broke my car?
    As long as the belt is still tight and there is no way for the bolt to loosen then you are fine to drive it to your mechanic. If the belt comes off your car will simply shut down as the serpentine belt controls most all of your vital parts.Help I broke my car?
    Remove the belt, the battery will carry you for 25 miles.Help I broke my car?
    oooo that is a tough one. I wouldnt be surprised either way. maybe it will break, maybe it will hold. I say go for it. You can run your car without the alternator for a while, but the battery has to be pretty charged for you to do that, it will eventually go dead. Good luck.Help I broke my car?
    I had something similar happen several years ago, not a Nissan though, it was a Chrysler and the alternator belt broke. I drove it to the nearest garage, 30 miles away with no problems except that they had to recharge my battery after replacing the belt, so you might get by with removing the belt for a short distance. No Guarantees though since I don't know anything about Nissans.



    Good Luck

    To Be A Car Mechanic?

    Is there any free online manuals or sites i could read to learn how to do certain things on cars? Like if i want to change an alternator I could go to the %26quot;Change An Alternator%26quot; section?To Be A Car Mechanic?
    http://www.autozone.com/servlet/UiBroker

    But that just shows how to take parts off and put them on for the most part. If you wanna be a real mechanic, you should learn how stuff works, so you know which parts need replacing.

    http://www.aa1car.com/library.htm

    That ought to keep you busy for a while. LOLTo Be A Car Mechanic?
    nothing thats free





    but if you can somehow get access to alldata......youd be setTo Be A Car Mechanic?
    some models you can find repair info for on autozone's website



    you can go to alldata.com and for a small fee,get access to repair info on your specific vehicle.



    Neat sites to go to find out about things is....howstuffworks.com

    or...ehow.com

    or aa1car.comTo Be A Car Mechanic?
    just google the car's repair instructions. LIke i would type in, for my car: Google: 93 bmw 325i service manualTo Be A Car Mechanic?
    Yes. Check out%26quot; www. Advanceautoparts.com%26quot; to start. In stead of on-line manuals they have on-line videos, they also have hand out pamphlet's in store on most auto repairs. You need to look around the trade stores were you live. Maybe you should look in to a vocational trade school in you area.The Auto parts have the hand out and on-line stuff. to help you change parts so you will buy from them. But remember %26quot;nothing is for free any more.%26quot; the real good trade reference auto manuals have charges to use there service. You might be ahead going to a book store and just buying a Auto repair manual. I have see some in collage book stores. I use to every 4/5 years buy a Motors %26quot;Motors Manual' just to keep up on change that the manufacture were making in there cars and truck. I now have boxes of manuals and auto repair manuals going back to the 40s. Hope you find what you are looking for. and good luck to you. I would have to go to back to school to learn how to work on new cars.

    The big 3 upgrade?

    How hard is this upgrade? Is this upgrade capable of being done without going to a shop? I want to purchase a HO alternator from eBay from a reliable source which I've heard of called Irragi alternators. I know what the big three means and it requires the upgrade of the following three power/ground cables which are the power wiring from the battery to the alternator, the ground from the battery to the chassis, and the ground strap to the engine/tranny to the chassis. How hard is it to change an alternator from a car and also the difficulty of upgrading the big 3?The big 3 upgrade?
    You can also just add to the existing factory wiring for the big 3 instead of replacing. Use the stock wires for the correct lengths needed for each.



    Aternators only need a properly adjusted tension on the belt to work properly.



    Difficulty is dependant on the design of the car.The big 3 upgrade?
    depending on the car it could be fairly easy or hard

    you can IM me if you want to know more

    1989 Mercury Tracer?

    My belts are tight, but they do show dry rot How do I change the Alternator %26amp; Power Steering belts on a 1989 Mercury Tracer. Nobody will touch it %26amp; to take it to a shop they want $250.00 just to change the belts. (my cost $15.00 for the belts). Also, the Alternator needs to be changed- any tips on how to do that?

    Thanks.1989 Mercury Tracer?
    Your best bet would be to get the Haynes manual for your car... it would be tough to give you step by step directions on here. You can get the manual at most any auto parts store... $15, and now you'll have it for any future projects.



    - Good Luck!1989 Mercury Tracer?
    I had one of those it sucked!!!1989 Mercury Tracer?
    Unless you have a good set of wrenches as well as a 1/2 inch drive socket set with the right sizes to fit the nuts and bolts, you can't do the job yourself. You will also need someone to lever the pump and alternator and hold it tight while you tighten the bolts. The job can be dangerous if you don't disconnect the battery properly and if it's required to get under a jacked up vehicle at any time. To get an idea of the cook book steps that would need to be followed for your car, go to the public library and read the Motors and Chilton's manuals for the repair. Also buy a http://www.haynes.com manual for your car.

    The gas dial on my 98 malibu is below the stop. how do i fix that.?

    i recently changed the alternator and had to disconnect my battery. after installing the new alternator i started the car and my gas gage was below e. it is stuck under the stop that it rests on when the car is off. when i start the car it springs up to the stop so it looks like the car is always out of gas. is there a way that i can fix this problem. i am not good with math and figuring out how much gas i have by way of how many miles i went is too much calculating.The gas dial on my 98 malibu is below the stop. how do i fix that.?
    You need to have it replaced. It sounds like it spun all the way around and ended up under the stop. Possible a tension spring has sprung inside the gauge. That means you may have to get a replacement cluster. Contact you local Chevy dealer to find out the proper procedures. Possible cost for a cluster? $200-$300? Plus the labor to remove and replace it---$90? Just giving ballpark figures so you know what you may be getting to.The gas dial on my 98 malibu is below the stop. how do i fix that.?
    honestly, you'd have to disassemble the cluster, open the gauge, and unstick it. (I know, not the answer you wanted)The gas dial on my 98 malibu is below the stop. how do i fix that.?
    the first answer you got is right.you can take a cluster out and remove the front lense.unstuck the needle.I did it a bunch of times on a malibu.
  • ex spouse
  • streamreader
  • This is to Lunatic72... I have no idea how to "let you know."?

    Here's what's wrong with my car...the thermostat gets stuck. My heater, and I say that loosly, blows cold air almost all the time. When I slow down it blows cold air, when I turn the amount of heat that is suppose to blow from low to high it blows cold air. It will blow slighly warm air only if I am going 60mph or greater and then only for a little while. May be 2 minutes. Then it blows cold again. Plus it doesn't blow very hard out of the vents. I was informed that it was the heating element. I'm guessing that the heating element and the heater core are the same thing? I can not afford to take it to a shop to fix and I do like to workon cars, I just don't have enough knowledge as to where and how to get to the heating element. I can take stuff off and put it back on that's not a problem. I have replaced alternators, changed spark plugs and I change my own oil. Plus I have put a starter on my dune buggie. So I'm not a complete idiot. But this heating element is getting the best of me.This is to Lunatic72... I have no idea how to %26quot;let you know.%26quot;?
    Start by replacing your thermostat... if it's sticking... your coolant never stays in the engine block long enough to get any form of heat from it... and without hot coolant flowing through your heater core... the fan will just blow cold. Thermostat is cheap and easy... start there for sure.This is to Lunatic72... I have no idea how to %26quot;let you know.%26quot;?
    try putting a higher temp. thermostat in. then check your fresh air intake and make sure there are no leaves or debris blocking it. As for the heater core, get ready to tear your dash half out to get to it. What kind of car?This is to Lunatic72... I have no idea how to %26quot;let you know.%26quot;?
    Like dr. deviance said, start with the easy cheap stuff like the thermostat. If its sticking thats a big part of why not not getting heat. And I was stating you could email me andlet me know all of this. What year, make and model is this car?This is to Lunatic72... I have no idea how to %26quot;let you know.%26quot;?
    Before changing anything, backflush the heater core. I thought my problem was the thermostat also but after fiddling around I did the flush. Easy enough to do. Take the heater core lines off of the engine and flush it with a garden hose. If you are not sure which one is the inlet and outlet, put the garden to both lines. Especially if its the GM red coolant. That will crystalize and gel up in the heater core. If that doesnt do it, then I would change thermostat before the heater core.This is to Lunatic72... I have no idea how to %26quot;let you know.%26quot;?
    i say again...shop manual..15 dollars...pays 4 itself...over n over....step by step on every job u do.. lists what tools needed..no one sez element...heater core will get less laughs...before u do anything are you really really really sure its the core????.. change thermostate,,flush system...flush heater core both directions seperatly...[where hoses go into engine fire wall]. refill 50/50 coolant/water....check heat door is working... we need more mechanic girls..good luckThis is to Lunatic72... I have no idea how to %26quot;let you know.%26quot;?
    You can pick up a good clue about this by feeling the heater hoses for temperature.That will show if hot coolant is entering the cab.If the line is hot near the engine but cooler away from it,something isn't letting it flow.Another possibility is an air lock in the system which can happen if it's been opened for some reason.I'm sure you know this already,but to be sure the coolant level is right,take off the radiator cap with the engine cool and top off the radiator.The first thing that happens when the coolant is low will be the heater acting up as you describe.This is to Lunatic72... I have no idea how to %26quot;let you know.%26quot;?
    your heater core is fine as long as you don't see water leaking on the passenger side floor, forget about the heater core, you need to put a new thermostat in the engine and if it doesn't fix the problem you need to look at the heater controls and make sure the duct doors are opening properly.